Schluter KERDI BOARD Tile Backer Board covers a broad range of application areas for creating level, waterproof substrates for the installation of ceramic and natural stone tiles. With suitable preparation of the joint areas, these structural panels may be used for officially approved bonded waterproofing assemblies.
Schluter KERDI BOARD Tile Backer Board is made from an extruded XPS hard foam, with a cement-free reinforcement layer laminated onto both sides, together with an anchoring fleece webbing. The surface of the board has gridlines consisting of 10 x 10 mm squares printed on one side. The board is waterproof and can withstand all chemical stresses that typically occur in conjunction with tile coverings, and is completely level and remains free of distortions and decay. It will not rot and is highly stable, even with one side exposed to temperature fluctuations and moisture.
Available in two different panel sizes: 1250mm x 625mm (0.78m²) or 2600mm x 625mm (1.62m²). These panels are available in thicknesses of 5, 9, 12.5, 19, 28, 38 and 50 mm.
Other variations include:
- Schluter KERDI BOARD V – a panel with vertical grooves cut into it for creating curved tile installation substrates.
- Schluter KERDI BOARD E – a 90° angled board component for creating corner formations and pipe panelling.
- Schluter KERDI BOARD U – a square U-shaped board component for creating pipe boxing.
- Schluter KERDI BOARD N – pre-fabricated niches for easy installation of a wall niche in tiled areas.
This board is suitable for: creating tile substrates on green masonry, existing substrates of all kinds and stud frames made of wood or metal; creating straight or curved (V) separating walls; concealing wall mounted installations and piping (pipe boxes – E / U); creating straight or curved (V) bathtub and shower surrounds; as well as creating work surfaces, vanities, storage shelves (N) or any other bathroom structures. The material is equally suitable for creating level substrates in floor renovation projects e.g. residential bathroom installations designed for foot traffic.
The board is easily cut to size with a utility knife. The gridlines printed on the surface are helpful for neat and quick installation. Panels can be fully adhered in wall areas or alternatively attached with dabs of adhesive. If necessary, the material may be secured with additional wall anchors, Schluter KERDI BOARD ZSD. In the case of stud frames made of wood or metal, the panels are attached with screws (Schluter KERDI BOARD ZS) and washers (Schluter KERDI BOARD ZT).
To create fully waterproof areas, all seams and joins in the board installation must be fully covered with the seaming tape Schluter KERDI KEBA (minimum width 12.5 cm), embedding it in the sealing adhesive Schluter KERDI COLL L. The seaming tapes should have at least 5 cm of overlap. Schluter KERDI KEBA band is also suitable for creating functional connections to fixed structural elements such as door openings or windows of metal, wood or plastic. For this purpose, apply Schluter KERDI FIX on the adhesive area of the fixed structures and Schluter KERDI COLL L on the adhesive area of the board and cover the entire joint area with sealing band.
Tiles can be installed directly over the board using the thin-bed method, but other suitable trowel applied coverings or plaster layers can be utilised, please contact Schluter for advice.
Thermal conductivity: DIN EN 12667 0.035 W/mK
Temperature resistance: –50 to +75°C
Material density (hard foam): DIN EN 1602 33 kg/m3
Water penetration capacity: 0
Water vapour diffusion resistance rating*: DIN EN 12086
Panel thicknesses 5, 9, 12.5 mm: µ = 1550
Panel thicknesses 19, 28, 38, 50 mm: µ = 440
Linear heat expansion coefficient: 0.007 mm/mK
Panel size 1250mm x 625mm cm: 0.78 m2
Panel size 2600mm x 625mm: 1.62 m2
Click here to view this product on the Manufacturers website.